The 10 Best Waterway Hot Tub Water Pump

This 4 Horse Power 56 Frame Pump Wet End fits Guangdong LX Brand Pump Motors only. These pumps usually have the part number WUA-400, WP-400 or LP-400 on the label. Watch the video for instruction on how to install this part and also how to determine if this is the correct part. It is about 7 1/4″” across the face of the pump, it measures about 7 3/8″ from the bottom to the top of the pressure side of the volute, it also measures 413/16″ from the back to front edge. The Suction and Pressure side thread fittings are called 2″ x 2″ but measure 3″ from the edge of the thread to the edge of the thread. NOTE: This Wet End looks a lot like an Aqua-Flo and a CMP Wet End but they do not interchange! Note: This Wet End Fits Guangdong Chinese LX and LP series Pumps only Some Pump Part numbers are as follows: (WUA400-II, WUA400-I) (LP400) (WP400-II/,400-I) To Install this wet end you will have to loosen the thru bolts and unscrew the impeller. There are time where you will have to disassemble the motor in order to loosen the impeller because they get stuck when they leak. Note: We offer parts for this wet end and complete pumps in our store. PLEASE NOTE: We did a lot of extra work with pictures and measurements so please do your part and measure your old part to be sure it is correct.. This will save us all some time and money.. Thanks.. Please note: When you have a seal leaking in most cases you will need an impellor because the leak caused water to get into the metal shaft area that the impeller is screwed onto and expands and damages See our You Tube Video for more information about this Pump “LX Series Guangdong Pump How To Repair The Spa Guy”

This is a gasket used with many different types of standard 2″ unions. One side of the gasket is flat and the other side has a raised O-Ring type of section. Outside Diameter: 2-15/16″ Inside Diameter: 2-1/8″

Not just a Filter Cartridge. Pleatco is a complete Filtration System! Pleatco Free Flow Cores, REEMAY Filtration Fabric, Antimicrobial Endcaps and Superbond Bands make the Pleatco product compass to differentiate the key components of why Pleatco Filter Cartridges are the best products on the market. Pleatco Free Flow cores allow for the free flow of water through the filtration fabric increasing the effectiveness of the filter.

HydroMaster High Performance Spa Pumps take reliability and durability to a new level. These premium-quality hot tub pumps are surprisingly affordable, so why bother attempting to repair your leaky, old, inefficient pump? Get a complete replacement (motor & wet end) for less than others charge for just a motor. You cannot buy a better quality spa pump at any price. 1-Yr. Warranty. UL Listed.

Waterway Plastics 56 frame Executive pump. 5 horse power, 230 volt, 60 Hz, 2″ intake, 2″ discharge. Two Speeds – 16.4 amps on high speed and 4.8 amps on low speed.

You are buying a 3 HP 48 Frame Waterway Executive 2″ X 2″ Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 12.0 Amps on the motor label on high speed.. The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Note: 315-1260 means nothing.The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8″ between or 5 3/16″ in a X Pattern and the 56 Frame will be 4 1/8″ Between or 5 3/4″ in a X Pattern. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. Note: Note: Note: There are some cases where a 12 Amp motor has a 4HP impeller so so if your motor has a 12.0 Amp Motor you need to check for the HP cast into the center of the impeller or look at the wear ring.. If the wear ring says 1, 2 or 3 then you have a 3HP impeller if it says 4 & 5 you have a 4HP. NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told they have 5 HP pumps, if you do the math two 5 HP pumps at 16 amps is 32 amps. Plus a 5.5 KW heater is 21 amps. That means with both pumps running and the heater on it will draw 53 AMPS. I bet your HOT TUB is on a 50 AMP breaker. Therefore contrary to what you have been told you DO NOT have a 5 or 6 or 7 Hp See our You Tube Video for more information about this Pump “How To Determine Which Wet End to Order Waterway Hot Tub Pump Executive Series The Spa Guy” Choose with care, If you return this part you pay shipping both ways.

You are buying a 2 HP 48 Frame Waterway Executive 2″ X 2″ Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows at 230V 10.0 Amps on the motor label on high speed 16.0A at 115V.. Example 2.8/8.0… The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Watch the Videos to learn about how to pick the correct wet end as well as how to repair your wet end and motor bearings too. The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8″ between or 5 3/16″ in a X Pattern and the 56 Frame will be 4 1/8″ Between or 5 3/4″ in a X Pattern. . We have done a lot of extra work with videos and pictures to prevent you from choosing the wrong part.. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told they have 5 HP pumps, if you do the math two 5 HP pumps at 16 amps is 32 amps. Plus a 5.5 KW heater is 21 amps. That means with both pumps running and the heater on it will draw 53 AMPS. I bet your HOT TUB is on a 50 AMP breaker. Therefore contrary to what you have been told you DO NOT have a 5 or 6 or 7 Hp See our You Tube Video for more information about this Pump “How To Determine Which Wet End to Order Waterway Hot Tub Pump Executive Series The Spa Guy” Choose with care, If you return this part you pay shipping both ways so be sure these are correct before ordering!

You are buying a 5 HP 48 Frame Waterway Executive 2″ X 2″ Wet End / Pump complete with Bleeder Barb & Silicon, Screws, Volute, Impeller, Seal, Face and the Wear Ring. This Wet End would fit a motor that shows 16.0 Amps on the motor label on high speed.. The Barb and Silicon is used in place of a plug for wet ends that have bleeders on them. Note: 315-1260 means nothing.The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts. The 48 Frame will be 3 5/8″ between or 5 3/16″ in a X Pattern and the 56 Frame will be 4 1/8″ Between or 5 3/4″ in a X Pattern. Look on the label of the motor for the two amperages if you have a 2 speed pump, if its a single speed look for a single amperage. It will look something like this: 10.0/3.5 The 10.0 is the high amperage in this example. 8.0 = 1 HP 10.0 = 2 HP 12.0 = 3 HP 14.0 = 4 HP 16.0 = 5 HP NOTE: Your pump or motor may say a different Horse Power than what you see here, DO NOT go by what is listed on the motor, go by the amperage on the label. Note: Note: Note: There are some cases where a 12 Amp motor has a 4HP impeller so so if your motor has a 12.0 Amp Motor you need to check for the HP cast into the center of the impeller or look at the wear ring.. If the wear ring says 1, 2 or 3 then you have a 3HP impeller if it says 4 & 5 you have a 4HP. NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told they have 5 HP pumps, if you do the math two 5 HP pumps at 16 amps is 32 amps. Plus a 5.5 KW heater is 21 amps. That means with both pumps running and the heater on it will draw 53 AMPS. I bet your HOT TUB is on a 50 AMP breaker. Therefore contrary to what you have been told you DO NOT have a 5 or 6 or 7 Hp See our You Tube Video for more information about this Pump “How To Determine Which Wet End to Order Waterway Hot Tub Pump Executive Series The Spa Guy” Choose with care, If you return this part you pay shipping both ways.

Genuine Waterway 4.0HP executive wet end , 56 frame, 2″suc./2″dis. Manufacturer: Waterway plastics is proud to design, engineer & produce our quality line of products right here in the USA.

Conclusion

By our suggestions above, we hope that you can found waterway hot tub water pump for you.Please don’t forget to share your experience by comment in this post. Thank you!