Which Is The Best Boat Fuel Water Filter

Sierra fuel water separators remove over 99.8% of emulsified water from your gasoline. Sierra’s 10 micron filters are over 90% efficient at removing particles as small as 10 microns. All filters flow @ 90 GPH to feed even the hungriest motor. Sierra 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems.

If you have difficulty in installing, you can go to YouTube to find the appropriate installation video:https://www.youtube.com/watch?v=LyeqTDVzY-A.

Specification:
1.Fuel Water Separating Filter fit 3/8 Inch NPT Outboard Motors as well.
2.Maximum Flow Rate 30 GPH (57 LPH).
3.Port / Connecting Size M18 X 1.5 Center Thread.
4.These are more suited to compact off road diesel equipment:tractors,skid steers loaders,movers.
5.Filter Rating 10 Micron.10 micron filters are over 90% efficient at removing particles as small as 10 microns. 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems, Designed to trap the smallest particles and emulsified water from Diesel.

Product details:
1.Don’t be caught in the water without one of these Diesel spin-on filters.
2.Filters are designed for high performance applications, and with flow rate of 30 GPH on the R12T model, your engine will perform better than ever with clean, water-free Fuel.
3.The inlet and out let can be feed in on the same side or in one side out the other side.
4.Check and replace regularly.

R12T water separator and filter complete combo installation instruction:
1.Nylon collection bowl down when installed the water separator and filter.
2.This filter has four ports, two inputs and two outputs. We provide two plugs for the extra two ports. If you need to use two plugs, you must install them to the filter and tighten them.
3.Before installing the filter, you have to remove those plugs, teflon-tape them, and re-install them.Prevent leaks from these plugs.
4.All of the above steps are very simple to operate, you can manually disassemble, and then use the tool to install tighten.

Sierra 18-7866 10 Micron, High Capacity Fuel Water Separator Filter for Yamaha MAR-FUELF-IL-TR

DETAILS
• Sierra Fuel Water Separators Remove over 99.8% of Emulsified Water from your Gasoline • Over 90% Efficient at Removing Particles as small as 10 Micron AND Flow at 90 GPH to Feed even the Hungriest Motor
• Sierra 10 Micron Filters are Recommended to prevent Damage to Sensitive Inboard, Sterndrive and Outboard Fuel Injection Systems
• Replaces: Yamaha MAR-FUELF-IL-TR
• Filter Size: High Capacity – 6″ or 152.4 mm
• Rating: 10 Micron
• Flow: 90 GPH

ABOUT SIERRA
Sierra is dedicated to protecting you and your investment. For 50 years Sierra, one of the most trusted names in the marine industry, has proudly been offering high quality engine and drive parts. Their products meet or exceed the original equipment part it replaces and are engineered to meet today’s high horsepower engine demands while withstanding the harsh marine environment.

SIERRA’S CUSTOMER SATISFACTION WARRANTY
All Sierra parts qualify for Sierra’s Industry Leading Customer Satisfaction Warranty. Sierra warrants its products to be free of defects in workmanship and materials for the useful life of the product. If a Sierra product fails to comply with the warranty, Sierra will repair or replace the defective product free of charge. The warranty is subject to additional terms, conditions and limitations. You can view Sierra’s full warranty located above in the Technical Specification Section.

The Moeller 033320-10 10 Micron Water Separating Filter Kit is designed for Mercury, Johnson, Evinrude, Yamaha, Suzuki, Honda, Tohatsu and Nissan engines, along with universal applications. Includes a powder coated reusable filter head, filter, barbs and plugs. Not recommended for use with electric fuel pumps.

Sierra 18-7945 10 Micron Fuel Water Separating Filter for Mercury/MerCruiser and Yamaha

DETAILS
• Sierra Fuel Water Separators Remove over 99.8% of Emulsified Water from your Gasoline • Over 90% Efficient at Removing Particles as small as 10 Micron AND Flow at 90 GPH to Feed even the Hungriest Motor
• Sierra 10 Micron Filters are Recommended to prevent Damage to Sensitive Inboard, Sterndrive and Outboard Fuel Injection Systems
• Replaces: Mercury/MerCruiser 35-802893Q01, 35-604941, 35-60494, 35-55501, 35-57250, 35-60494A5, 35-806771, 35-8052691, 35-802893Q, 35-807172 and Yamaha ABB-FUELF-IL-TR
• Filter Size: Long – 4.35″ or 110.5mm
• Rating: 10 Micron
• Flow: 90 GPH

ABOUT SIERRA
Sierra is dedicated to protecting you and your investment. For 50 years Sierra, one of the most trusted names in the marine industry, has proudly been offering high quality engine and drive parts. Their products meet or exceed the original equipment part it replaces and are engineered to meet today’s high horsepower engine demands while withstanding the harsh marine environment.

SIERRA’S CUSTOMER SATISFACTION WARRANTY
All Sierra parts qualify for Sierra’s Industry Leading Customer Satisfaction Warranty. Sierra warrants its products to be free of defects in workmanship and materials for the useful life of the product. If a Sierra product fails to comply with the warranty, Sierra will repair or replace the defective product free of charge. The warranty is subject to additional terms, conditions and limitations. You can view Sierra’s full warranty located above in the Technical Specification Section.

Replaces Mercury 35-60494-1.
Replaces Racor S3213, B32013,18-7932-1,18-7932,18-7928-1,18-7928.
Filter Replaces Mercury Marine 35-809097,Racor S3213,Yamaha MAR-24563-03-00,18-7919,18-7919-1.

To replace element:
1.Drain the unit by loosen the drain screw.
2.Loosen and remove the filter element.
3.Loosen and remove the bowl from filter element.Please note the bowl is reusable,do not dispose unless broken.
4.Wipe O-ring gland clean,and coat bowl’s seal O-ring with fresh oil or grease and place it back to the gland.Then tighten the bowl onto filter element firmly by tool.
5.Coat filter element’s seal O-ring with fresh oil or grease and attach filter element onto filter head,and the tighten securely by tool.
6.Run engine and check for fuel leakage.

Attention:
1.Make sure you remove both the filter and the filter bowl from the mounting housing and put a light film of fuel on the o-ring.As delivered it will leak without the lubrication to allow for the proper crush.
2.For diesel transfer tank to filter the fuel before it enters the main tank.Only thing is you have to make sure to get the proper sealant for the threads. For The First time installation,in order to avoid any leaking at the threads.You’d better get some thread paste since the tape might plug the injectors if it were to come loosen.
3.Check and replace regularly.

Instructions:
To Drain Water:
1.Loosen drain screw to drain bowl of water.
2.Tighten drain screw.
3.Run engine and check for fuel leakage.

Safety Warning:
Periodically check fittings and filter element for leaks.Be careful when changed fuel filter element.Diesel is extremely flammable and highly explosive under certain conditions.Avoid spilling diesel.Always stop engine and do not smoke or allow open flames in the area while changing filter element.

Replaces Mercury 35-60494-1 and Universal.

How use?
1.Before installing the filter, please check those Tubing and plugs,PTFE-tape is use to Prevent leaks from these plugs.
tips:1m PTFE-tape include.
2,install the plugs,Connect the fuel pipe and use the Hose Clamp to lock.
3.All of the above steps are very simple to operate, you can manually disassemble, and then use the tool to install tighten.

replace element:
1.Drain the unit by loosens the drain screw.
2.Loosen and remove the filter element.
Please ensure that the assembly is stable.
3.Loosen and remove the bowl from filter element.Please note the bowl is reusable,do not dispose unless broken.
(Professional tools may be required to remove bowls and filter element)
4.Wipe O-ring gland clean,and coat bowl’s sealing O-ring with clean oil or grease and place it back to the gland.The tighten the bowl onto filter element firmly by hand.
5.Coat filter element’s sealing O-ring with clean oil or grease and attach filter element onto filter head,and the tighten securely by hand.
6.Run engine and check for fuel leakage.

Instructions
To Drain Water:
1.off engine,Loosen drain screw to drain bowl of water.
2.Tighten drain screw.
3.Run engine and check for fuel leakage.
Warning:
Periodically check fittings and filter element for leaks.Be careful when changing fuel filter element .Gasoline is extremely flammable and highly explosive under certain conditions.Avoid spilling gasoline.Always stop engine and do not smoke or allow open flames in the area while changing filter element.

Tips:
replace element by tool
replace element at regular.
CHECK THE ELEMENT SUGGEST:EACH 7000KM/400 HOURS.

Package include:
1 IVSPEED S3213 assy
1*1M PTFE tape
1*Memo sticker for time or KM when use
2*Miniature Stainless Worm Gear Hose Clamp
1*Manual(some mode)

Conclusion

By our suggestions above, we hope that you can found boat fuel water filter for you.Please don’t forget to share your experience by comment in this post. Thank you!