minmommy 
Nowadays, there are so many products of pentek water filter 20×4.5 in the market and you are wondering to choose a best one. You have searched for pentek water filter 20×4.5 in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings pentek water filter 20×4.5 which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
41,282 Reviews Scanned
Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2"
- Reduces chlorine taste and odor in drinking water
- Granular activated carbon (GAC) media with spun polypropylene core and polypropylene end caps for strength
- Porous polyethylene 70-micron outer shell reduces carbon fines and other particles
- Initial pressure drop of 0.90 psi at a flow rate of 4 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
Pentek 155358, DGD-5005-20 Dual Gradient Density Polypropylene Sediment Cartridge
This Pentek DGD-5005-20 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The nominal filtration rating of the pre-filter layer is 50 microns, and the rating of the post-filter layer is 5 microns. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 20 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating (pre-filter) | 50 microns |
| Nominal filtration rating (post-filter) | 5 microns |
| Initial pressure drop at 20 gpm | <1> |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-1/2 inches (508 x 114 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 150233, Big Blue, 1" In/Out, #20 Blue/Black, HFPP, w/ PR
- Large filter housing for high-flow and heavy sediment applications
- Reinforced polypropylene sump for strength and chemical resistance
- Use with a 20” x 4-1/2” filter cartridge (sold separately)
- Pressure relief button for easier cartridge replacement
- Initial pressure drop of 1 psi at a flow rate of 15 gpm
This Pentek 150233 20-BB 1” #20 Big Blue filter housing with pressure relief is suitable for high-flow and heavy sediment applications. The opaque blue sump is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene (HFPP) for stiffness. The black cap has 1” female National Pipe Thread Taper (NPT) threaded input and output connections and a nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. The housing can be used with a 20” x 4-1/2” filter cartridge (sold separately). It has an initial pressure drop of 1 pound per square inch (psi) at a flow rate of 15 gallons per minute (gpm), a maximum operating pressure of 90 psi, and a maximum operating temperature of 100 degrees F (37.8 degrees C). This filter housing meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various high-flow applications, including residential drinking water filtration, food service, and irrigation, among others.
Specifications
| Filter cartridge size (H x W) (sold separately) | 20 x 4-1/2 inches (508 x 114 mm) |
| Initial pressure drop at 15 gpm | 1 psi |
| Maximum temperature | 100 degrees F (37.8 degrees C) |
| Maximum pressure | 90 psi |
| Maximum dimensions (H x W) | 23-3/8 x 7-1/4 inches (594 x 184 mm) |
| Materials and structural integrity certification | NSF/ANSI standard 42 |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek DGD-5005 Spun Polypropylene Filter Cartridge, 10" x 4-1/2"
- Reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water
- Combines two separate gradient layers for higher efficiency and dirt-loading capacity
- Spun polypropylene for resistance to chemicals and bacteria
- Initial pressure drop of less than 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C).
This Pentek DGD-5005 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The nominal filtration rating of the pre-filter layer is 50 microns, and the rating of the post-filter layer is 5 microns. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 10 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating (pre-filter) | 50 microns |
| Nominal filtration rating (post-filter) | 5 microns |
| Initial pressure drop at 10 gpm | <1> |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 10 x 4-1/2 inches (254 x 114 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 155263, RFFE20-BB Radial Flow Iron Reduction Cartridge
This Pentek 155263 RFFE20-BB radial flow iron reduction cartridge is suitable for reducing the presence of dissolved iron in water supplies with concentrations up to 3 parts per million (ppm) for improved taste, less staining, and reduced chance of pipe and water heater damage. It is designed for use with a #20 Pentek Big Blue filter housing (not included), and operates at a maximum temperature of 100 degrees F (37.8 degrees C). It has a lifespan of 26,000 gallons for water supplies with an iron concentration of 3 ppm, and a longer lifespan at lower concentrations. This iron reduction cartridge is suitable for residential and commercial filtration applications, with pre-sediment and post-carbon treatment recommended for best results.
Specifications
| Lifespan at 3 ppm | 26,000 gallons |
| Lifespan at 2 ppm | 40,000 gallons |
| Lifespan at 1 ppm | 80,000 gallons |
| Lifespan at 0.5 ppm | 160,000 gallons |
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems under the Pentek brand. The company, founded in 1966 and headquartered in Schaffhausen, Switzerland, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek R30-20BB Pleated Polyester Filter Cartridge, 20" x 4-1/2", 30 Microns
- Reduces sand, dirt, silt, rust, and scale particles in residential and commercial water
- Nominal filtration rating of 30 microns
- Non-woven polyester media pleated around a polypropylene core for strength
- Initial pressure drop of less than 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
This Pentek R30-20BB pleated polyester filter cartridge reduces sand, dirt, silt, rust, and scale particles in residential and commercial water. It has a nominal filtration rating of 30 microns at an efficiency of 85%. The filter is made of resin-impregnated cellulose and polyester media pleated around a polypropylene core for strength. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 10 gallons per minute (gpm), and operates over a temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C). This pleated polyester filter cartridge is for use in various applications, including drinking water purification, irrigation, and industrial processes, among others.
Specifications
| Nominal filtration rating | 30 microns |
| Initial pressure drop at 10 gpm | <1> |
| Temperature range | 40 to 125 degrees F (4.4 to 51.7 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-1/2 inches (508 x 114 mm) |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 150467 20-BB 3/4" Big Blue Filter Housing with Pressure Relief
Pentek NCP-20BB Pleated Carbon-Impregnated Polyester Filter Cartridge, 20" x 4-1/2", 10 Microns
- Reduces sediment and chlorine taste and odor in residential and municipal drinking water
- Nominal filtration rating of 10 microns
- Carbon-impregnated polyester media pleated around a polypropylene core for strength and resistance to bacteria
- Initial pressure drop of 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
This Pentek NCP-20 pleated carbon-impregnated polyester filter cartridge reduces sediment and chlorine taste and odor in residential and municipal drinking water. It has a nominal filtration rating of 10 microns at an efficiency of 85%. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 50% in up to 1,000 gallons at a flow rate of 4 gallons per minute (gpm). The cartridge is made of carbon-impregnated polyester media pleated around a rigid polypropylene core with plastisol end caps for strength and resistance to bacteria. It has an initial pressure drop of 1 pound per square inch (psi) at a recommended flow rate of 10 gallons per minute (gpm), and operates over a temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C). This filter cartridge is for use in rural, residential, and municipal drinking water purification.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 10 gpm | 1 psi |
| Chlorine reduction capacity | 1,000 gallons at 4 gpm |
| Temperature range | 40 to 125 degrees F (4.4 to 51.7 degrees C) |
| Maximum dimensions (H x W) | 20 x 2-1/2 inches (508 x 114 mm) |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 50%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2" (Pack of 2)
- Reduces chlorine taste and odor in drinking water
- Granular activated carbon (GAC) media with spun polypropylene core and polypropylene end caps for strength
- Porous polyethylene 70-micron outer shell reduces carbon fines and other particles
- Initial pressure drop of 0.90 psi at a flow rate of 4 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
This Pentek RFC20-BB carbon filter cartridge reduces chlorine taste and odor in residential and commercial drinking water. It is made of granular activated carbon (GAC) media with a spun polypropylene core and polypropylene end caps for strength, and there is a nitrile butadiene rubber (Buna-N) gasket to ensure a watertight seal. The filter has a porous polyethylene 70-micron outer shell to reduce carbon fines and other suspended particles in the filtered water. It will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 75% in up to 70,000 gallons at a flow rate of 4 gallons per minute (gpm). The filter has an initial pressure drop of 0.90 pounds per square inch (psi) at a recommended flow rate of 4 gpm, and operates over a temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C). This carbon filter cartridge is used for treatment of residential and commercial drinking water.
Pentek 1" Threaded 20" Genuine Big Blue Filter Housing Kit | Complete with Bracket, Screws and Wrench (150233 150061 144368)
- HIGH FLOW – HEAVY SEDIMENT : Large filter housing for high-flow and heavy sediment applications
- COMPLETE KIT : Housing comes with Stainless Steel Bracket, Screws and Wrench – Guaranteed to fit!
- QUALITY MATERIALS : Reinforced & High-Flow Polypropylene, Stainless Steel bracket & Screws
- PRESSURE RELIEF : Pressure relief button to remove pressure for easier cartridge replacement
- WARRANTY : One year limited warranty – see Pentek Inc. for details
This complete kit comes to you from Better H2O Products Inc which includs :
✪ Genuine Pentek 1″ #20 Big Blue filter housing (Pentek # 150233) with pressure relief valve,
✪ Genuine Pentek stainless steel bracket with stainless steel screws (Pentek # 150061) [which will not rust like white painted ones]
✪ Genuine Wrench (Pentek # 144368)
✪ All guaranteed to fit!
Don’t assume the parts will fit – order the complete kit!
All parts of this kit come neatly packaged in a single box
► Initial pressure drop of 2 psi at a flow rate of 15 gpm
►Suitable for high-flow and heavy sediment applications
►Whole home filtration, food and service, irrigation and more applications
►Opaque blue sump is made from reinforced polypropylene for strength and chemical resistance
►Black cap is made from high-flow polypropylene (HFPP) for stiffness
►1” female National Pipe Thread Taper (NPT) threaded input and output connections
►Nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal
►Pressure relief button on inlet to release pressure for easier filter changes
►Can be used with a 20” x 4-1/2” filter cartridge (sold separately)
►Maximum operating pressure of 90 psi
►Maximum operating temperature of 100 degrees F (37.8 degrees C)
►NSF 42 Certified for quality assurance
Conclusion
By our suggestions above, we hope that you can found pentek water filter 20×4.5 for you.Please don’t forget to share your experience by comment in this post. Thank you!
