minmommy 
Nowadays, there are so many products of 3d printer water cooling in the market and you are wondering to choose a best one. You have searched for 3d printer water cooling in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings 3d printer water cooling which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
3D Printer All Metal Water-Cooled Hotend Bowden-fed Liquid Cooling Hot End, for Titan Aqua Water Cooling, for High Temperature 3D Printing peek PA
- Filament Size: 1.75mm
- nozzle size: 0.4mm
- Package: Only 1 hotend, No wires
- the heating block with 3.1mm hole for temperature sensor will be shipped with the hotend, so that customer can use it for thermocouple like PT100, K-type and so on.
- Compared with the air cooling hotend,the highly efficient liquid cooling can be effective for any currently available 3D printing materials.
Nozzle diameter: 0.4mm
Feed inlet diameter : 1.75 diameter Inlet
We use the Red hard plastic material fittings (suitable for OD4mm guiding tube), so that the connector be more stable.
Our hotend is made with high quality material, and great drilled.
BXQINLENX SC600 DC 12V PC CPU Water Cooling System Tool Water Pump 132.09 GPH 10W Brushless Drive Water Pump for Destop Computer Laptop Computer
LENX SC600 DC 12V PC Cpu Water Cooling System Tool Water Pump 132.09 GPH 10W Brushless Drive Water pump for Destop Computer Laptop computer
Specifications:
Power consumption:10W
Rated voltage: DC 12V
Rated current: 0.8A
Max flow rate: 500L/H (132.09G/H)
Max static head: 3m (9.8ft)
Diameter of inlet:Female G 1/4″
Diameter of outlet:Female G 1/4″
Lifespan: More than 50,000hrs
Power supply: DC electric source
Ceramic shaft + ceramic bushing
Speed:3000 RPM
Size:length 9 cm, height 8 cm, width 6cm.
NOTE:
1. Working at rated voltage (DC12V/0.8A). The positive pole is red wire, the negative pole is black wire,white wire is test wire.
2. This pump is centrifugal pump, it can’t vent the air automatically, so it must be operated by submersible installation. (If outside water installation, you should make sure it is installed below the liquid surface)
3. When blocking, long-running is not allowed.
4. Preventing any hard particles entering the pumps.
5. Ceramic bearing, graphite sleeve, very quiet, when using anhydrous idling is forbidden
Package:
1 X Water pump
Arctic MX-4 – Thermal Compound Paste for Coolers | Heat Sink Paste | Composed of Carbon Micro-Particles | Easy to Apply | High Durability – 4 Grams (1 Pack)
- [BETTER THAN LIQUID METAL]: Composed of carbon micro-particles which lead to an extremely high thermal conductivity. It guarantees that heat generated from the CPU or GPU is dissipated efficiently.
- [SAFE APPLICATION]: The MX-4 is metal-free and non-electrical conductive which eliminates any risks of causing short circuit, adding more protection to the CPU and VGA cards.
- [HIGH DURABILITY]: In contrast to metal and silicon thermal compound, the MX-4 does not compromise over time. Once applied, you do not need to apply it again as it will last at least for 8 years.
- [EASY TO APPLY]: With an ideal consistency, the MX-4 is very easy to use, even for beginners.
- [THERMAL COMPOUND]: Formula, the MX-4 guarantees exceptional heat dissipation from the components and supports the stability needed to push your system to its limit.
Thermal Compound for All CoolersEasy to ApplyWith an ideal consistency, the MX-4 is very easy to use, even for beginners. The possibilities for its application and the most effectively way to avoid voids between CPU and cooler we show you in the video.Safe Application:It does not contain any metallic particles so electical conductivity would not be an issue. Unlike silver and copper compound, it ensures that contact with any electrical pins would not result in damage of any sort.High Durability :In contrast to metal and silicon thermal compound, the performance of MX-4 does not compromise over time. Once applied, you do not need to apply it a second time as it will last at least for 8 years. Value for MoneyA high performance thermal compound perfect for system builders, there’s no suprise that the MX-4 exceeds your expectations for its low price tag. Thermal Conductivity 8.5 W/(mK) Viscosity 870 poise Density 2.50 g/cm³ Volume Resistivity 3.8 x 1013 Ω-cm
ARCTIC MX-4 2019 Edition – Thermal Compound Paste – Carbon Based High Performance – Heatsink Paste – Thermal Compound CPU for All Coolers, Thermal Interface Material – High Durability – 4 Grams
- The new version of the #1 bestseller: the MX-4 Edition 2019 convinces everyone with its usual quality and performance, that have always distinguished it
- Better than liquid metal: composed of carbon micro-particles which lead to an extremely high thermal conductivity. It s that heat generated from the CPU or GPU is dissipated efficiently
- Thermal compound: The MX-4 Edition 2019 formula S exceptional heat dissipation from the components and supports the stability needed to push your system to its limit
- Safe application: The MX-4 Edition 2019 is metal-free and non-electrical conductive which eliminates any risks of causing short circuit, adding more protection to the CPU and VGA cards
- High durability: in contrast to metal and silicon thermal compound, The MX-4 Edition 2019 doesn’t compromise over time. Once applied, you do not need to apply it again as it will last At least for 8 years
ARCTIC offers innovative solutions incessantly – changing impossible user requirements into new. Always focused on our customers, ARCTIC is devoted to deliver excellence through a strong dedication and a high sense of commitment. In light of the ever-changing consumer landscapes, we aspire to continue to expand and diversify our products and solutions. From computer cooling and peripherals to audio and digital home entertainment, we strive to enrich people’s lives by creating innovative, user friendly yet affordable products with a great value of benefit. For us value for money is a key factor – a constant our customers rely on.
Similar items with 4 stars and above
eSUN ePA 1.75mm Nylon 3D Printer Filament Natural 1kg Spool (2.2lbs) Spool, Natural ePA
eSUN 3D Printer Filament: ePA (Nylon)
Note: ePA Nylon is sensitive to moisture. Always keep it dry before and during printing.
Extrusion Temperature Range: 230_ to 260_
Color:
Natural Semi-transparent
eSUN 3D printing filament is tested, and confirmed to work with all FDM 3D printers, with a dimensional accuracy better than +/- 0.05mm
Smart Desktop Jet 3D Printer JGAURORA A5S Prusa I3 Home School DIY Use Full Metal Frame Large Print Volume 305X305X320mm Color Touch Screen Resume Print Filament Runs Out Detection
- Large build size: 305*305*320mm （12*12*12.6in）, you can print your creations with more sizes and small pieces in one time.
- BDG Heated Platform: Allows easy removable of printed model and save masking tape.
- Filament RUN-OUT detection : The machine beeps when filament runs out to remind you to change new filament quickly, save your time for printing.Power Failure Protection: Resume print from where the last print was stopped due to power failure, advoid from failure printing.
- Still 30 sets of 3pcs MK8 MK9 Hotend Heater Protect for the next 30 clients (15 USD of extra value)
- Better customer experience, high print accuracy and high speed with quiet working, suit for school and home.And most importantly ,we offer 12 months warranty and maintenance from the date of your purchase
Nozzle Quantity : 1
Layer thickness : 0.1-0.3mm
Filament Diameter：1.75mm
Build volume：305*305*320mm
Accuracy：0.2mm
Print speed：10-150mm/s
Nozzle diameter：0.4mm
Nozzle temp.：180~240’C
Hotbed temp.：room temp.~100’C
Machine size:538（length）*553（width）*543（height）mm
Machine weight：13.5KG
Packing size: 640*600*255mm
Packing weight:15.5kg
Power:300W
Package :
● 1xA5
● 1x Spool filament PLA （0.25KG）
● 1x Power Supply Cable
● 1x Tool box ( Hex Wrench Kit and testing filament)
● 1× USB disk (contains software, test sample files and operation manual)
PETG 3D Printer Filament 1.75mm, Diameter Tolerance +/- 0.05 mm, 1 KG （2.2lbs）Spool, 1.75 mm PETG Filament for 3D Printer (Transparent Orange)
- 1KG net (approximately 2.2 lbs) Filament with black Spool
- TRONXY PETG 3D Printer Filament Vacuumed Sealed With Desiccant
- 1.75mm Filament Diameter (Dimensional Accuracy +/- 0.05mm)
- Recommended Extrusion/Nozzle Temperature 230C – 250C
- Spool Diameter: 8″ – Spool Width: 2.50″ – Spool Hub Hole Diameter: 2.05″ – Inner Circle Diameter: 3.5″
Conclusion
By our suggestions above, we hope that you can found 3d printer water cooling for you.Please don’t forget to share your experience by comment in this post. Thank you!
