minmommy 
Nowadays, there are so many products of 20 x 4.5 water filter pentex in the market and you are wondering to choose a best one. You have searched for 20 x 4.5 water filter pentex in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings 20 x 4.5 water filter pentex which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
16,068 Reviews Scanned
Pentek 155358, DGD-5005-20 Dual Gradient Density Polypropylene Sediment Cartridge
This Pentek DGD-5005-20 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The nominal filtration rating of the pre-filter layer is 50 microns, and the rating of the post-filter layer is 5 microns. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 20 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating (pre-filter) | 50 microns |
| Nominal filtration rating (post-filter) | 5 microns |
| Initial pressure drop at 20 gpm | <1> |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-1/2 inches (508 x 114 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2"
- Reduces chlorine taste and odor in drinking water
- Granular activated carbon (GAC) media with spun polypropylene core and polypropylene end caps for strength
- Porous polyethylene 70-micron outer shell reduces carbon fines and other particles
- Initial pressure drop of 0.90 psi at a flow rate of 4 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
Pentek DGD-5005 Spun Polypropylene Filter Cartridge, 10" x 4-1/2"
- Reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water
- Combines two separate gradient layers for higher efficiency and dirt-loading capacity
- Spun polypropylene for resistance to chemicals and bacteria
- Initial pressure drop of less than 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C).
This Pentek DGD-5005 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The nominal filtration rating of the pre-filter layer is 50 microns, and the rating of the post-filter layer is 5 microns. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 10 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating (pre-filter) | 50 microns |
| Nominal filtration rating (post-filter) | 5 microns |
| Initial pressure drop at 10 gpm | <1> |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 10 x 4-1/2 inches (254 x 114 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 150233, Big Blue, 1" In/Out, #20 Blue/Black, HFPP, w/ PR
- Large filter housing for high-flow and heavy sediment applications
- Reinforced polypropylene sump for strength and chemical resistance
- Use with a 20” x 4-1/2” filter cartridge (sold separately)
- Pressure relief button for easier cartridge replacement
- Initial pressure drop of 1 psi at a flow rate of 15 gpm
This Pentek 150233 20-BB 1” #20 Big Blue filter housing with pressure relief is suitable for high-flow and heavy sediment applications. The opaque blue sump is made of reinforced polypropylene for strength and resistance to chemicals, and the black cap is made of high-flow polypropylene (HFPP) for stiffness. The black cap has 1” female National Pipe Thread Taper (NPT) threaded input and output connections and a nitrile butadiene rubber (Buna-N) O-ring to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. The housing can be used with a 20” x 4-1/2” filter cartridge (sold separately). It has an initial pressure drop of 1 pound per square inch (psi) at a flow rate of 15 gallons per minute (gpm), a maximum operating pressure of 90 psi, and a maximum operating temperature of 100 degrees F (37.8 degrees C). This filter housing meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is for use in various high-flow applications, including residential drinking water filtration, food service, and irrigation, among others.
Specifications
| Filter cartridge size (H x W) (sold separately) | 20 x 4-1/2 inches (508 x 114 mm) |
| Initial pressure drop at 15 gpm | 1 psi |
| Maximum temperature | 100 degrees F (37.8 degrees C) |
| Maximum pressure | 90 psi |
| Maximum dimensions (H x W) | 23-3/8 x 7-1/4 inches (594 x 184 mm) |
| Materials and structural integrity certification | NSF/ANSI standard 42 |
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek 150467 20-BB 3/4" Big Blue Filter Housing with Pressure Relief
Pentek DGD-5005-20 5 Micron 20 x 4.5 Comparable Whole House Sediment Water Fi.
- QUICK & EASY INSTALLATION: Quick and easy installation into your 20 x 4.5 Inch Big Blue whole house filtration system
- 6 MONTH FILTER LIFE: By replacing your water filter every 6 months , depending on the quality of your water, you keep your water tasting great with the Tier1 SDC-45-2005
- HIGH QUALITY FILTRATION: This Tier1 155358-43 spun-polypropylene sediment filter reduces sediment, dirt, particulates, sand, and silt
- REPLACEMENT PART FOR MANY PART NUMBERS & MODELS: This filter is comparable to many 5 Micron 20 x 4.5 sediment filter. Replace your old Pentek DGD-5005-20 or Liquatec SDF-45-2005 with a Tier1 SDF-45-2005
- 100% TIER1 NO WORRIES GUARANTEE: We stand behind the quality of filtration and overall performance of our Tier1 filters!
Geekpure Whole House Big Blue Water Filter Housing 1-Inch Outlet/Inlet with Wrench and Bracket -4.5 Inch x 20 Inch – Clear Housing
- Complete set 20 inch big clear housing,1″NPT inlet/outlet,with plastic wrench,screw and metal bracket.
- Clear housing allows you to see when you need to change filters and everything else works as it should.Housing only, filter cartridges are sold separately .
- Fits all standard sized 4-1/2 inch diameter by 20 inch whole house cartridges.Fits NSF standard,Large capacity housing for high flow applications.
- It is Installed at the main water supply and produce pure water for your entire home. Enjoy better water from every tap and every appliance in the whole house.
- Pack of 1,Housing only. filter cartridges are sold separately.
Tier1 Replacement for Pentek R30-20BB 30 Micron 20 x 4.5 Pleated Polyester Sediment Water Filter 4 Pack
- QUICK & EASY INSTALLATION: Quick and easy installation into your 20 x 4.5 Inch Big Blue whole house filtration system.
- 6 MONTH FILTER LIFE: By replacing your water filter every 6 months , depending on the quality of your water, you keep your water tasting great with the Tier1 R30-20BB Water Filter
- HIGH QUALITY FILTRATION: This Pentair R30-20BB Comparable Tier1 filter reduces sediment, dirt, rust, and particles.
- REPLACEMENT PART FOR MANY PART NUMBERS & MODELS: This filter is comparable to many 30 Micron 20 x 4.5 inch pleated polyester sediment filter. Replace your old Pentek R30-20BB Pleated Polyester filter with a Tier1 R30-20BB
- 100% TIER1 NO WORRIES GUARANTEE: We stand behind the quality of filtration and overall performance of our Tier1 filters!
Pentek 150560 3/4" #20 3G Standard Clear Housing with Pressure Relief
Conclusion
By our suggestions above, we hope that you can found 20 x 4.5 water filter pentex for you.Please don’t forget to share your experience by comment in this post. Thank you!
